Do you serve my city, town or ZIP code?
Melissa is inside the territory this office covers, along with Allen, Anna, Celina, Fairview, Frisco and Little Elm. Coverage follows your address rather than how far out a town sounds, so if you are near the edge of that list, give the cross streets or your ZIP code on the call and you will get a straight yes or no before anyone is scheduled.
The town I am in is not the one in your name — do you still come out here?
The city in the office name is where it is based, not the limit of where it works: Allen, Anna, Celina, Fairview, Frisco and Little Elm are covered the same way Melissa is. Franchise territories are drawn by area rather than by the single town on the sign, which is why the name on the door and the town on your mail often differ. Confirm your address on the call rather than ruling yourself out.
How quickly can a crew reach my address?
That depends on where in Melissa you are, the roads, and what the crews already have running, so any single figure published here would be guesswork. The phone is answered around the clock, and you get an honest arrival window for your own address on that call. If water is still coming in, say so first — the steps to take while you wait matter more than the drive time.
Do you work on rentals, condos, businesses and manufactured homes here?
Rentals, condos, storefronts, restaurants and manufactured homes are all routine work, and the building type changes the access and the drying plan more than it changes the method. ANSI/IICRC S500 sorts a loss into Class 1 through 4 by how much water the structure absorbed and how hard it is to dry, which reads the same in a crawl space as in an office. Who pays — owner, tenant or association — is set by your lease, declaration and master policy, so read yours.
Do you rebuild and repair afterward, or only dry it out?
Both halves are one job. The first is mitigation — extraction, removing material that cannot be dried, and documented drying against a dry standard — and ANSI/IICRC S500 ties what has to come out to the water category, one through three. The second is reconstruction: framing repair, insulation, drywall, trim, paint and flooring put back. How much of each your loss needs depends on what the water reached, so that scope is written after the inspection.
Do you repair and repaint water-damaged drywall and ceilings?
Wet gypsum board and the insulation behind it usually come out rather than dry in place, and the cut is typically carried 12 to 24 inches above the visible water line because the material wicks upward past the stain. That put-back is part of the job: hanging, taping, three coats of compound with drying time between them, texture and paint. On homes built before 1978, the EPA's Renovation, Repair and Painting Rule governs how painted surfaces are disturbed.
Can one estimate cover both the cleanup and the rebuild, and what does the repair cost?
One inspection can produce both scopes, and carriers generally prefer it that way — mitigation and repair as line items in one claim file, priced from the Xactimate database the adjuster uses. No one should quote the repair figure sight unseen. It firms up when materials reach the dry standard ANSI/IICRC S500 requires and hidden damage is open to view, commonly three to five days of drying, though yours may need more or less. Any charge for the inspection is stated on the call.
Do you replace the flooring and subfloor, or do I hire a flooring contractor?
Subfloor, underlayment and finished flooring are all part of the repair scope, and so is the framing underneath when a joist is wet. Replacement goes back under the National Wood Flooring Association's installation guidance, which is why new wood cannot go down until the subfloor and the flooring are no more than two to four percentage points apart in moisture content. Whether a floor is dried in place or replaced depends on the material and the water category.
Does your own crew do the rebuild, or is the reconstruction subcontracted?
The rebuild usually stays on one contract, with the same project manager who ran the drying and a single claim file, though that varies by market. Which trades are in-house and which are outside trade partners varies too — drywall, paint, tile, cabinetry and flooring are not always the same crew, so ask on the call who will be in your home. Structural and electrical put-back is pulled under permit and inspected by the local building department, usually under the International Residential Code.
Will insurance pay for the rebuild, and how do repairs get approved?
Coverage for the repair usually rides on the same claim as the mitigation, and approval runs off the written scope rather than a lump sum: the adjuster reviews line items and the moisture logs ANSI/IICRC S500 calls for, then approves or asks for a supplement when something hidden turns up. Replacement-cost policies typically pay in two steps, actual cash value first and the held-back depreciation after the work is finished and invoiced. Like-kind-and-quality wording varies by policy, so read yours.
Can you repair just the damaged section, or does the whole floor or ceiling have to be replaced?
Patch repairs are common and often the right call. What forces a bigger replacement is the water itself: ANSI/IICRC S500 sorts water into Categories 1 through 3, and Category 3 means porous material in the wet zone comes out, however small that zone is. Assembly matters too — a single ceiling panel in a grid swaps out, while taped drywall and sheet goods have no seam to stop at. Matching is the other limit, since tile and flooring run in dye lots.
How long does the rebuild take once the drying is finished?
The rebuild cannot start until the structure meets the dry standard ANSI/IICRC S500 requires, because closing a wall over wet framing traps the moisture. After that, a single wet room — drywall hung, taped, three coats of compound with drying time between each, then paint and flooring — commonly runs a couple of weeks, while a loss across several rooms, cabinetry on order or a permit inspection runs longer. Your schedule depends on what the scope turns out to be.
Do you handle the finish work too — cabinets, vanities, baseboards, tile and grout?
Cabinets, vanities, countertops, baseboards, tile and grout are part of the put-back, and they are usually the last trades in because they go over finished surfaces. Substrate condition governs the tile: ANSI A108 allows no more than 1/8 inch of variation in 10 feet for tile with an edge 15 inches or longer, so a repaired floor gets flattened before setting. Which items are replaced and which are refinished depends on the material and how wet it got.
If only part of the floor got wet, is the rest of the continuous floor replaced so it matches?
Carriers generally pay to replace what the moisture readings document as wet, and whether the rest of an undamaged run comes with it turns on the policy's like-kind-and-quality wording and on whether the flooring continues through a doorway without a transition. Put that question to the adjuster in writing, with photographs, before the repair is approved. Most policies also include an appraisal provision — two appraisers and an umpire — for disputes over the amount of loss, and your state insurance department takes complaints.
